# Valley flashing, too much?

**URL:** <https://forum.nachi.org/t/valley-flashing-too-much/67140>\
**Category:** Roofing Inspections\
**Created:** [February 28, 2012, 4:46pm UTC](https://forum.nachi.org/t/valley-flashing-too-much/67140 "2012-02-28T16:46:48Z")\
**Posts on this page:** 12\
**Page:** 1

<div class="post-metadata">

**Author:** ![chagler](https://avatars.discourse-cdn.com/v4/letter/c/5e9695/32.png) [@chagler](https://forum.nachi.org/u/chagler)\
**Post date:** [February 28, 2012, 4:46pm UTC](https://forum.nachi.org/t/valley-flashing-too-much/67140/1 "2012-02-28T16:46:48Z")

</div>

Can anyone think of something writable for this? It may work just fine but it doesn’t look right.

![flashing.jpg](https://global.discourse-cdn.com/internachi/original/3X/0/c/0c8cb28cdf76fd3fc62424773f5ad1629ed9337d.jpeg)

---

<div class="post-metadata">

**Author:** ![jfunderburk](https://sea2.discourse-cdn.com/internachi/user_avatar/forum.nachi.org/jfunderburk/32/187920_2.png) [@jfunderburk](https://forum.nachi.org/u/jfunderburk)\
**Post date:** [February 28, 2012, 5:09pm UTC](https://forum.nachi.org/t/valley-flashing-too-much/67140/2 "2012-02-28T17:09:34Z")

</div>

Is that flashing rusting?

R905.2.8.2 Valleys. Valley linings shall be installed in accordance  
with the manufacturer’s installation instructions before  
applying shingles.Valley linings of the following types shall be  
permitted:

1. For open valleys (valley lining exposed) lined with  
metal, the valley lining shall be at least 24 inches (610  
mm) wide and of any of the **corrosion-resistant metals** in  
Table R905.2.8.2.

2. For open valleys, valley lining of two plies of mineral  
surfaced roll roofing, complying with ASTM D 3909 or  
ASTM D 6380 Class M, shall be permitted. The bottom  
layer shall be 18 inches (457 mm) and the top layer a  
minimum of 36 inches (914 mm) wide.

3. For closed valleys (valley covered with shingles), valley  
lining of one ply of smooth roll roofing complying with  
ASTM D 6380 and at least 36 inches wide (914 mm) or  
valley lining as described in Item 1 or 2 above shall be  
permitted. Self-adhering polymer modified bitumen  
underlayment complying with ASTM D 1970 shall be  
permitted in lieu of the lining material.

Permitted metals from Table R905.2.8.2

1. Cold-rolled copper
2. Lead-coated copper
3. High-yield copper
4. Lead-coated high-yield copper
5. Aluminum
6. Stainless steel
7. Galvanized steel
8. Zinc alloy
9. Lead
10. Painted terne

---

<div class="post-metadata">

**Author:** ![jfunderburk](https://sea2.discourse-cdn.com/internachi/user_avatar/forum.nachi.org/jfunderburk/32/187920_2.png) [@jfunderburk](https://forum.nachi.org/u/jfunderburk)\
**Post date:** [February 28, 2012, 5:11pm UTC](https://forum.nachi.org/t/valley-flashing-too-much/67140/3 "2012-02-28T17:11:49Z")

</div>

> [@chagler](#):
>
> Can anyone think of something writable for this? It may work just fine but it doesn’t look right.

I don’t have any problems with the amount of flashing and where it’s located and would advise against getting into a pizzing contest with a licensed roofer or builder based on your opinions unless you are also licensed and competent in the area of roofing. My only problem is with the corrosion.

---

<div class="post-metadata">

**Author:** ![chagler](https://avatars.discourse-cdn.com/v4/letter/c/5e9695/32.png) [@chagler](https://forum.nachi.org/u/chagler)\
**Post date:** [February 28, 2012, 5:16pm UTC](https://forum.nachi.org/t/valley-flashing-too-much/67140/4 "2012-02-28T17:16:47Z")

</div>

Yes it is rusting pretty bad. Matter of fact all of the flashings were. I did note that for repair/replacement.

---

<div class="post-metadata">

**Author:** ![jhaynes](https://avatars.discourse-cdn.com/v4/letter/j/ce7236/32.png) [@jhaynes](https://forum.nachi.org/u/jhaynes)\
**Post date:** [February 28, 2012, 7:46pm UTC](https://forum.nachi.org/t/valley-flashing-too-much/67140/5 "2012-02-28T19:46:38Z")

</div>

Then that all you need to write up…design can be a separate issue…kind of like flat roofs…its not IF they will fail but WHEN they will fail…we don’t speculate as to the when but report what IS going on at time of inspection.

regards

Jeff

---

<div class="post-metadata">

**Author:** ![dmacy](https://sea2.discourse-cdn.com/internachi/user_avatar/forum.nachi.org/dmacy/32/1466_2.png) [@dmacy](https://forum.nachi.org/u/dmacy)\
**Post date:** [February 28, 2012, 9:23pm UTC](https://forum.nachi.org/t/valley-flashing-too-much/67140/6 "2012-02-28T21:23:57Z")

</div>

“Poor roof design may lead to premature failure of the roofing system”

---

<div class="post-metadata">

**Author:** ![rernst1](https://sea2.discourse-cdn.com/internachi/user_avatar/forum.nachi.org/rernst1/32/176650_2.png) [@rernst1](https://forum.nachi.org/u/rernst1)\
**Post date:** [February 28, 2012, 9:37pm UTC](https://forum.nachi.org/t/valley-flashing-too-much/67140/7 "2012-02-28T21:37:28Z")

</div>

On the left side it appears the one piece of flashing is on top of the shingles and then slightly below that it appears the flashing stops short so water could get under that piece.

---

<div class="post-metadata">

**Author:** ![wmisegades](https://avatars.discourse-cdn.com/v4/letter/w/8edcca/32.png) [@wmisegades](https://forum.nachi.org/u/wmisegades)\
**Post date:** [March 2, 2012, 7:38am UTC](https://forum.nachi.org/t/valley-flashing-too-much/67140/8 "2012-03-02T07:38:02Z")

</div>

“Rust was noted on the open valley flashing. All exposed flashings should be painted to prevent from deterioration.”

---

<div class="post-metadata">

**Author:** ![ryoung7](https://sea2.discourse-cdn.com/internachi/user_avatar/forum.nachi.org/ryoung7/32/188798_2.png) [@ryoung7](https://forum.nachi.org/u/ryoung7)\
**Post date:** [March 7, 2012, 1:59am UTC](https://forum.nachi.org/t/valley-flashing-too-much/67140/9 "2012-03-07T01:59:38Z")

</div>

R905.2.8.2 Valleys.  
Non destructive. Unless you have home owners permission to do a technical.  
R905.2.8.2 manufacturer’s installation instructions before  
applying shingles

1. For open valleys (valley lining exposed) lined with  
metal, the valley lining shall be at least 24 inches (610  
mm) wide and of any of the **corrosion-resistant metals** in  
Table R905.2.8.2.  
We can’t see under the valley or the main shingles.  
The starter shingle is your observation.  
\*\*corrosion-resistant metals  
**Galvanized has a coating. I have seen this rust before. Depends on the gauge it might be superficial.Rust proofing.  
Call it out anyway.  
Recommend a licensed roofer.**

**I see one problem. Top valley.  
Shingle in the metal valley.  
It should be clear.**  
\*\*

---

<div class="post-metadata">

**Author:** ![Frank\_Albert](https://sea2.discourse-cdn.com/internachi/user_avatar/forum.nachi.org/frank_albert/32/947_2.png) [@Frank\_Albert](https://forum.nachi.org/u/Frank_Albert)\
**Post date:** [March 7, 2012, 12:20pm UTC](https://forum.nachi.org/t/valley-flashing-too-much/67140/10 "2012-03-07T12:20:03Z")

</div>

> [@wmisegades](#):
>
> “Rust was noted on the open valley flashing. All exposed flashings should be painted to prevent from deterioration.”

This is the correct response.  
Considering the roof design, that system is as good as it’s going to get. The shingle running under that L. valley piece isn’t an issue. It may have been the only way to get a conforming closure there. It’ll be OK.

---

<div class="post-metadata">

**Author:** ![ryoung7](https://sea2.discourse-cdn.com/internachi/user_avatar/forum.nachi.org/ryoung7/32/188798_2.png) [@ryoung7](https://forum.nachi.org/u/ryoung7)\
**Post date:** [March 7, 2012, 12:32pm UTC](https://forum.nachi.org/t/valley-flashing-too-much/67140/11 "2012-03-07T12:32:54Z")

</div>

_ **Considering the roof design, that system is a sgood as it’s going to get** _. The shingle running under that L. valley piece isn’t an issue. It may have been the only way to get a conforming closure there. It’ll be OK.  
I disagree.  
It is a good system.  
Do not get me wrong.  
All the signs are there that experienced roofers performed due diligence to there trade.  
The materials provided by the company are what they have to work with.  
The manufactures are responsible for there materials.

---

<div class="post-metadata">

**Author:** ![Frank\_Albert](https://sea2.discourse-cdn.com/internachi/user_avatar/forum.nachi.org/frank_albert/32/947_2.png) [@Frank\_Albert](https://forum.nachi.org/u/Frank_Albert)\
**Post date:** [March 7, 2012, 11:06pm UTC](https://forum.nachi.org/t/valley-flashing-too-much/67140/12 "2012-03-07T23:06:53Z")

</div>

> [@ryoung7](#):
>
> _ **Considering the roof design, that system is a sgood as it’s going to get** _. The shingle running under that L. valley piece isn’t an issue. It may have been the only way to get a conforming closure there. It’ll be OK.  
> I disagree.  
> It is a good system.  
> Do not get me wrong.  
> All the signs are there that experienced roofers performed due diligence to there trade.  
> The materials provided by the company are what they have to work with.  
> The manufactures are responsible for there materials.

I agree and understand. You said it better than I was going to bother with. (I leave a lot unsaid.) You are correct.
